Dometic NDR1292 Operations Instructions download pdf (Page 4)

INSTALLATION

GENERAL INSTRUCTION

This appliance is designed for storage of foods

and storage of frozen foods and making ice.

The refrigerators outlined herein have been design cer-

tified by A.G.A. under the ANSI Z21.19 Refrigerator

Standard for installation in a mobile home or recreational

vehicle and are approved by the Canadian Gas Asso-

ciation.

The certifications are, however contingent on the instal-

lation being made in accordance with the following in-

structions as applicable.

In the U.S.A., the installation must conform with:

1. National Fuel Gas Code ANSI Z223.1-(latest edition)

2. Manufactured Home Construction and Safety Stan-

dard, Title 24 CFR, Part 3280.

3. Recreational Vehicles ANSI A119.2-(latest edition).

The unit must be electrically grounded in accordance

with the National Electric Code ANSI/NFPA 70-(latest

edition) when installed, if an external alternating current

electrical source is utilized.

4. Any applicable local code.

In CANADA, the installation must conform with:

1. Current CAN/CGA B149 Gas Installation Codes

2. Current CSA Standard Z240.4 GAS-EQUIPPED

RECREATIONAL VEHICLES AND MOBILE HOUS-

ING.

3. Where a flexible metal connector is used, it must

comply with the provisions of the current Standard

CAN1-6.10, METAL CONNECTORS FOR GAS

APPLIANCES.

4. Any applicable local code

The unit must be electrically grounded in accordance

with the current CANADIAN ELECTRICAL CODE C22

Parts 1 and 2.

VENTILATION

The installation shall be made in such a manner as to

separate the combustion system from the living space

of the mobile home or recreational vehicle. Openings for

air supply or for venting of combustion products shall

have a minimum dimension of not less than 1/4 inch.

Proper installation requires one lower fresh air intake

and one upper exhaust vent. The ventilation kits shown

in this instruction manual have been certified for use with

the refrigerator models listed in the table. For "

Certified

Vent System Kits

" see page 15. The ventilation kits

must be installed and used without modification. An

opening toward the outside at floor level in the refrigera-

tor compartment must be provided for ventilation of

heavier-than-air fuel gases. The lower vent of the recom-

mended kits is provided with proper size openings. The

flow of combustion and ventilating air must not be ob-

structed.

The lower side vent is fitted with a panel which provides

an adequate access opening for ready serviceability of

the burner and control manifold of the refrigerator.

This should be centered on the back of the refrigerator.

GAS CONNECTION

Hook-up to the gas supply line is accomplished at the

manual gas valve, which is furnished with a 3/8" SAE

(UNF 5/8" -18) male flare connection. All completed

connections should be checked for leaks with soapy

water.

! WARNING

DO NOT use a flame to check for gas leaks.

The gas supply system must incorporate a pressure

regulator to maintain a supply pressure of not more than

11 inches water column.

When testing the gas supply system at test pressures in

excess of 1/2 psig, the refrigerator and its individual

shutoff valve must be disconnected from the gas supply

piping system.

When testing the gas supply system at pressures less

than or equal to 1/2 psig, the appliance must be isolated

from the gas supply piping system by closing its individ-

ual manual shutoff valve.

In case detailed instructions on the installation and

connection to the gas supply are required, contact your

dealer or distributor.

ELECTRICAL CONNECTION

120 Volts AC Connection

The refrigerator is equipped with a three-prong (ground-

ing) plug for your protection against shock hazards and

should be plugged directly into a properly grounded

three-prong receptacle. DO NOT cut or remove the

grounding prong from this plug. The free length of the

cord is 2 feet and therefore recommended that the

receptacle be located to the right side of the refrigerator

(viewed from the rear) and approximately 10 inches from

the floor (see FIG. 3). This allows easy access through

the vent door. The cord should be routed to avoid direct

contact with the burner cover, flue cover or any other

components that could damage the cord insulation.

12 Volts DC Connection

The refrigerator model NDR 1292 require a continuous

12 volt DC supply (even though 2-way models are

designed to operate on 120 volts AC and gas, a 12 volt

FIG. 3

10"

120 Volt AC

receptacle

1 2 3 4 5 6 7 8 9 ... 15 16

Comments to this Manuals

No comments

Dometic NDR1292 Operations Instructions Page 4

Comments to this Manuals

Related products and manuals for Fridges Dometic NDR1292